Control4 Rroom-based control system Instrukcja Konfiguracji Pobierz pdf

™

• N’essayezpasderechargerunebatteriemoinsquelabatteriesoit

spciquementmarqu«rechargeable».

• Nevousdbarassezjamaisdesbatteriesdansunfeu.

VORSICHT! Das Batteriekurzschluß, -durchsickern oder -abbruch

verhindern:

• Benutzen Sie AA alkalische Batterien nur im Schalter.

• Mischen Sie nicht Batteriearten, wie alkalische und nachladbare NiMH

Batterien.

• Versuchen Sie nicht, eine Batterie neuzuladen, es sei denn die Batterie

ist speziﬁsch gekennzeichnetes „nachladbares.“

• Entledigen Sie nie sich Batterien in einem Feuer.

ConguretheRemoteControl

1 Start Composer and connect to a Director.

2 In the System Design view (selected by default), select the room where the

System Remote Control will reside.

3 In the My Drivers tab, locate the SR-250 under the User Interface section.

4 Double-click SR-250 to add the device to the project tree.

5 Identify the SR-250:

• In the Connections view, click the Network tab.

• Select System Remote Control SR-250 in the center pane.

• Click Identify (or right-click and choose Identify).

• When prompted to do so, press the red 4 button four (4) times to have the

device identify to the Control4 system.

Note: To complete the identiﬁcation process, the System Remote Control

must be on the same ZigBee channel as the Controller; the Controller

must have Zserver enabled. If you need to change the ZigBee channel on

the System Remote Control, see Step 7.

• When the MAC address appears in the window, click Close.

6 View or change the System Remote Control properties as needed in

Composer: In the System Design view in the project tree, select the System

Remote Control SR-250 object to display the device’s properties.

UseandFeatures

Control4 System Remote Control SR-250 (Model C4-SR250B-Z-B) is intended for

use in a Control4® system with OS 2.0 and later. It is included with the purchase

of select Control4 Controllers, but may also be purchased separately. This System

Remote Control can be used to:

• Navigate system menus and access media databases on a television or

monitor

• Navigate system menus and access media databases in its own display

window

• Control system devices

This System Remote Control goes beyond a typical “universal” remote that simply

learns IR codes from TVs, VCRs, CD players, and DVD players. This device features:

• Bi-directionalcommunicationwithsystemcomponents

• ZigBeewirelessmeshnetworking

• Fullaccesstosystemcomponents

• Back-lightingonkeysanddisplayforeaseofuseindarkrooms

• Ambientlightsensorforefcientcontrolofbacklighting

• Quick-accessbuttonstoselectrecentlyusedaudioandvideodevices

• Programmablebuttons

• Pagingfunctionality

• Standardcontrolfeaturesfor:DigitalSatelliteSystems(DSS),cableboxes,TVtuners,

DigitalVideoRecorders(DVR),DVDchangers/players,CDchangers/players,MP3

players,VCRs,orTVs.

• Poweredbyfour(4)AAbatteries(included)

InstallandMaintaintheBatteries

Install the Batteries

Install the four (4) AA batteries (included) into the back of the SR-250. Insert them

according to the diagram provided in the battery compartment (with the + and -

terminals aligned correctly).

Battery Use and Care Tips

• Keep the battery contacts and compartment clean.

• Remove the batteries from the product if it is not going to be used for

several months.

• Extreme temperatures reduce battery performance. Avoid putting the SR-250

in very warm places.

Battery Replacement Safety Rules

WARNING!To prevent a battery short, leakage or rupture:

• UsetypicalAAAlkalinebatteriesonly.

• Donotmixbatterytypes,suchasAlkalineandrechargeable

NiMHbatteries.

• Donotattempttorechargeabatteryunlessthebatteryisspecically

marked“rechargeable.”

• Neverdisposeofbatteriesinare.

ATTENTION!Pour empêcher court-circuiter, fuite ou rupture de batterie:

Utilisez les accumulateurs alcalins typiques d’AA seulement.

• Nemlangezpaslestypesdebatterie,telsquelesbatteriesalkalines

etrechargeablesdeNiMH.

System Remote

Control SR-250

Setup Guide

The properties include:

• Display Brightness—Set the light level (brightness) of the screen backlight.

Choose a percentage from 0 (O) to 100 (full brightness).

• Keypad Brightness—Set the light level (brightness) of the keypad backlight.

Choose a percentage from 0 (O) to 100 (full brightness).

• Sleep Mode—Set how long the System Remote Control stays awake after

no activityThe default setting is 15 seconds, but can be extended up to 60

seconds or can be reduced down to 0 to conserve battery life.

• Battery Level—Displays the current strength of the batteries.

• Channel—Displays the ZigBee channel set for the SR-250, which should

match the ZigBee channel for the Controller.

• Gateway—Displays the MAC address of the Zigbee Server (usually your

Controller unless you specify dierently).

• MAC—Displays the System Remote Control’s own MAC address.

• Firmware Version—Displays the current ﬁrmware version.

7 Check or change the ZigBee Channel: If you need to change the ZigBee

channel to match the Controller’s channel (which is sometimes changed to

improve reception), do the following at the SR-250:

• Press the List button, and then select Info > Conﬁg.

• Press buttons 2, 4, 8, 6, #, *, List (in that order) to get into Edit mode.

• On-menu List, Info, and Conﬁg:

-Display Brightness

-Keypad Brightness

-Motion Detect

-Battery Level

-Factory Default

-About

• Press the up or down arrows to change the ZigBee channel.

• Press List to exit Edit mode and save the changes.

ProgramtheProgrammableButtons

On the System Remote Control SR-250, you can program six (6) soft buttons (Red,

Green, Yellow, Blue, *, and #) to perform programmed activities.

These buttons can be programmed to execute any of the AV device’s macros or IR

codes. Program these options using the AV device properties page.

1 Start Composer and connect to a Director.

2 Ensure the System Design view is selected.

3 Ensure that you have the following devices in your project:

• Controller

• System Remote Control SR-250

• An AV device to be controlled

4 Select the Connections view.

5 On the Network tab, ensure the Controller and the System Remote Control

are both network identiﬁed (have a network address).

6 Program the programmable buttons (Red, Green, Yellow, Blue, *, or #) either

based on the selected AV device or the selected room.

Based on AV Device (Pictured):

• Select the System Design view.

• Select an AV device to display the device’s Properties page.

• On the device’s Properties page, choose Code or Macro for the button you

want to program, and then choose a code or macro from the drop-down list,

edit the Help text as needed, and then choose Set.

Note: Help text describes custom programming to end-users under the

House option in any of the Navigators.

For example:

(1) In System Design view, select Disc Changer.

(2) Under Red button, choose Code.

(3) From the drop-down list, choose Subtitle.

(4) Choose the Set button to create a Subtitle button.

Based on Room:

• Select the Programming view.

• Select a room in the Device Events pane.

• Select the Commands radio button in the [Room] Events pane.

• Use the drop-down menu to select a command or button (such as “Blue

Button”).

• Build the script using items from the Actions pane to program the actions

desired in the selected room when you select the command or button.

• For more information about programming, see the Composer Pro User Guide.

ProgramSystemRemoteControlPaging

You can conﬁgure the Beep paging feature of the SR-250 through programming.

This feature can be used to page a lost System Remote Control. A keypad or

custom button can be programmed to cause the System Remote Control to beep

when pressed. This lets the user ﬁnd the lost System Remote Control.

To program the paging feature for this System Remote Control:

1 Start Composer and connect to a Director.

2 Select the Programming view.

3 Select the Event that you want to use to start the page. For example, to

select a keypad button press, ﬁrst select the keypad under the Device Event

section (on the left), and then select the button under Events.

4 In the Actions list (on the right), select System Remote Control SR-250.

5 In the Commands list, choose an action for the System Remote Control, and

then double-click the green arrow to add the action to the Script pane.

1 2 3 4

Podsumowanie treści

Strona 1 - Setup Guide

™• N’essayezpasderechargerunebatteriemoinsquelabatteriesoitspciquementmarqu«rechargeable».• Nevousdbarassezjamaisdesbatter

Strona 2

Strona 3 - Regulatory Compliance

™control4.com | 888.400.4070 ™Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the

Strona 4

™control4.com | 888.400.4070 ™Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the

Więcej dokumentów dla Sprzęt rejestrujący Control4 Rroom-based control system

Aby wyświetlić dokument Control4 Rroom-based control system Dokumentacja

Control4 Rroom-based control system Dokumentacja (134 strony)

Control4 Rroom-based control system Dokumentacja (17 strony)

Aby wyświetlić dokument Control4 Rroom-based control system Instrukcja Użytkownika

Control4 Rroom-based control system Instrukcja Użytkownika (4 strony)

Aby wyświetlić dokument Control4 Rroom-based control system Podręcznik Użytkownika

Control4 Rroom-based control system Podręcznik Użytkownika (25 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Control4 Rroom-based control system Instrukcja Konfiguracji

Przeglądaj online lub pobierz Instrukcja Konfiguracji dla Sprzęt rejestrujący Control4 Rroom-based control system. Control4 Rroom-based control system Setup guide Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Sprzęt rejestrujący Control4 Rroom-based control system

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt rejestrujący Control4 Rroom-based control system